Autel PowerScan PS100 Electrical System Diagnostics
Autel PowerScan PS100 Generation Description:
Autel PowerScan PS100 is the best electrical tester for reducing diagnostic time in all 6- to 30-volt vehicle electrical systems. After a simple hook-up of the tool to the vehicle's battery, you can:
1. Test for continuity with its built-in auxiliary ground lead.
2. Determine at a glance if a circuit is positive, negative, or open without having to reconnect clips from one battery pole to another.
3. Test for poor ground contacts instantly without performing voltage drop tests. The tool is also short-circuit protected; its internal circuit breaker will trip if it becomes overloaded.
4. By depressing the power switch, conduct a positive or negative battery current to the probe tip for testing the function of an electrical component without the use of jumper wires.
5. Follow and locate short circuits without wasting fuses. The tool's long cable allows you to test along the entire length of the vehicle without constantly searching for suitable vehicle grounds.
Autel PowerScan PS100 Features:
Circuit breaker protected
Extremely easy to use and highly reliable
Built-in Flashlight enables you to work in the dark
Instantly identifies positive, negative and open circuits
Instantly checks continuity of switches, relays and diodes
20ft (extendable) cable provides excellent accessibility to test along the vehicle
Easy to read AVOmeter allows you to read voltage, current and resistance at the fingertip
Simultaneously uses the hot lead and the ground lead to activate components right in your hand
Audio tone indicator allows for no-look menu scrolling once users are familiar with menu tone assignment
Tests for bad ground contacts instantly, allowing you to follow and locate shorts fast without wasting fuses
With a flip of the power switch, you have an instant hot/ground lead for powering up electrical components like cooling fans, relays, etc.
Performs every type of service including power injection, measurement, ground testing, polarity checks, continuity testing and components activation.
Provide Every User with Fast, Accurate, Agile Testing
Not only does the Autel vehicle circuit diagnostic tester PS100 has the power to complete every type of circuit test for vehicles, but it can also provide users with the most rapid and accurate testing outcomes. After numerous testing and verifications, we make sure that Autel PS100 can provide ready-to-read data without any delay. The LCD display will read the DC voltage with a resolution of 0.1 volts, even when you test low voltage, the numeral it reads can still be accurate.
What's more, it has a built-in scope function, and you can use Autel circuit tester PS100 to probe sensors and get a visual scope pattern on the probe. With the advanced processor, waveforms like cam sensors, crank sensors, and fuel injectors can be captured easily.
Circuit Breaker to Protect Overloaded
You are able to conduct a full battery current to the tip of the probe when you press the switch forward.
The built-in circuit breaker is a nice feature to protect users, the test tool, as well as the vehicle components, ensures their safety. Simply connect the extra ground lead to the tool and press the power switch forward and it will trip the circuit breaker. This will prevent power from going to the tip but still allow you to use the tool as a multimeter. When you are away from vehicle components, simply press the reset button and you are ready to power up again.
Autel PowerScan PS100 Head Light to Help You Work in Dark:
PS100 has a headlight, which helps the technicians and mechanics to illuminate dark environments for better diagnoses. With this feature, there is no need for you to have another illuminating device when you want to diagnose circuits in corner areas or dim environments. Besides, Autel circuit tester PS100 also has a tone feature to make different sounds for mechanics to distinguish testing results in dark area.
DC Voltage
While the circuit testing tool is in this mode, contacts the probe tip to a circuit, then the LCD display will read the DC voltage with a resolution of 0.1 volts.
DC Mode is the mode that the PS100 can supply battery power or ground by pressing the rocker switch.
DC mode is for testing DC (direct current) voltages.
Voltage testing is as easy as contacting the probe tip to a circuit and reading the display.
AC Voltage
While the circuit tester tool is in this mode, contacts the probe tip to a circuit, then the LCD display will read the Max. voltage, the Min. voltage, frequency, and duty cycle.
You can adjust the sampling frequency by pressing the Up/Down Button.
The auxiliary ground wire is connected to one end of the circuit under test, and the probe contacts the other end of the test circuit.
The LCD will display the max and mini voltage value, and display the signal waveform in real-time
PS100 Power Circuit Probe Kit Resistance Testing Mode
The probe contacts one end of the measured resistance, and the auxiliary ground lead is connected to the other end of the measured resistance. The LCD will display the resistance between the tip and auxiliary ground lead. Can be used as a continuity test.
NOTE: When the resistance value is less than 30Ω, the instrument buzzer will alarm and the green LED will light.
Tone On/Off
While the tester is in this mode, just do a quick press of the mode button to toggle the tone on or off. While quickly pressing (a quick press and release) the mode button, if a short high beep is heard, this means the audio tone is turned on. If a short low beep is heard, the audio tone is turned off.
This function is invaluable when working in bright areas where LED illumination alone is not sufficient. The audio feature may be disengaged when desired, such as for applications where the tool will be connected to circuits for long periods of time and the audio could become annoying.
PS100 Circuit Tester Can Output Electrodes
Contact the probe tip to the bulb positive terminal, and connect the auxiliary ground lead to the bulb negative terminal.
Press up to output positive electricity, and press down to output negative electricity.
The screen will display the forward voltage drop, which indicates forward bias.
If swapping the probe tip with auxiliary ground lead, the screen will not display voltage, which indicates reverse bias.
Autel PS100 FAQ, click here.
Autel PowerScan PS100 Reviews, click here.
Autel PowerScan PS100 Specifications:
Display: |
TFT color display (160 x 128 dpi) |
Operating Temperature: |
0 to 60°C (32 to 140°F) |
External Power: |
12.0 or 24.0 V power provided via vehicle battery |
Length\Width\Height: |
126mm(4.96")\46.5mm(1.83")\35mm(1.38") |
NW: |
0.105kg (0.23lb),GW: 0.726 kg(1.6lb) |
Autel PowerScan PS100 Package List:
1pc x PS100 main unit
1pc x Probe Tip
1pc x 20ft. Externsion cable
1pc x Cigarette lighter adapter
1pc x Battery hookup clips
1pc x User Manual
1pc x Rugged blow molded case
Autel 11th Anniversary Sale, Buy Over $500 USD, Get a Free Gift. (Date: 8.30-9.28)
2023 New Autel APB130, APB130 with XP400 PRO - Add Key For VW MQB NEC35XX
Autel Update Serivce Mega Sale, No Limitation, Up to 25% Off
Two Years Free Update: for IM608 II, IM508S, Elite II, IM608 Pro, IM508, OTOFIX D1, OTOFIX D1 Lite, OTOFIX IM1 MP808Z-TS, MP808S, MP808BT PRO OTOFIX IM2.
US / UK / EU Ship 2 Years Free Update 2023 Autel MaxiIM IM608 II (IM608 PRO II) Full Kit, Buy Now to Get 2pcs of OTOFIX Watches (values 398USD) & Autel IMKA APB112 G-BOX2 Adapter and Two pcs of Ikeys For Free.
2023 Autel Maxicom MK908 PRO II $1649 US UK EU Ship
Autel FAQ FB
Contact information:
Whatsapp: 86-13559259264
Email: sales@Autelsale.com
Skype: Sales@AutelSale.com
If you have any problems, please do not hesitate to contact us. We respond to our email on 7/24.