cart

How to Do All Key Lost with Autel MaxiIM IM608 and XP400 and APA106 (Dump Mode) for Range Rover 2018?


How to Do All Key Lost with Autel MaxiIM IM608 and XP400 and APA106 (Dump Mode) for Range Rover 2018?

How to Do All Key Lost with Autel MaxiIM IM608 and XP400 and APA106 (Dump Mode) for Range Rover 2018?

YouTube video link:
https://www.youtube.com/watch?v=B8XTzFXbnnA
(Note: If you encounter any type of problem during the process, please upload the datalog on the top-right corner after failing to perform the functions. Please connect your device to the network while performing the following functions.)

Specific add key ( all key lost ) procedure is as follows:
all key lost procedure

Click "Manual Selection"

Click

Click "Range rover"

Click

Click "2015"

Click

Click "Chave inteligente"

Click

Read "Operate Guide" carefully before starting the procedure.

Read operate guide carefully before starting the procedure.

The procedure is as follows:

Start Key Writing


Steps for learing a smart key with the Start Key Writing function:
1. Remove the RFA and read its data
2. Save the data ( default save path: scan/UserData/JLRData )
3. Perform the Start Key Writing function to generate new data
4. Write the new data back to the RFA and assemble the vehicle
5. Verify the key function

For details, refer to the operation introduction for the Start Key Writing function in the operation guide.

Note: There is no emergency start function for the newly added key.

Start Key Writing Procedure

RFA (also called KVM) module located:

RFA (also called KVM) module located

Remove the module:

Remove the module

And remove the case

And remove the case

De-solder the crystal:

De-solder the crystal

De-solder the capacitor:

De-solder the capacitor

Solder the lines
T1 and T2 are the components of capacitor and crystal.

Solder the lines T1 and T2 are the components of capacitor and crystal

After you have connected the MCU to the programmer XP400 with APA106 cable:


Step 1: Click "Read Chip Status" to check if the MCU is locking or unlocking (read chip from MCU);
Step 2: Click "Read / Write chip data (Secured)" to read MCU Dflash and eeprom file.
Step 3: Click "Start Key Writing", use the Dlash and eeprom file to make dealer key and write the new created Dflash file and eeprom file back to MCU
Step 4: Click "Read / Write chip data (Secured)" to write new data back to MCU.

Connect MCU to the programmer XP400 with APA106 cable

Click "Read Chip Status"

Click

Click "Locking"


Click

Click "Read / Write chip data (Secured)"

Click

Click "Read MCU Data"

Click

Note: This function requires connection to the programmer XP400.
Please follow the operation guide to connect with the chip correctly.

Note: This function requires connection to the programmer XP400.

Click "D-FLASH"

Click

Read the data successfully, click "OK" to save the data

click

Dflash file name
Click "Confirm" to save the Dflash file.

Dflash file name

File path to save the Dflash: 
( default save path: scan/UserData/JLRData )

File path to save the Dflash

Click "EEPROM"

Click "EEPROM"

Read the data successfully, click "OK" to save the data.

Read the data successfully, click

File path of eeprom file, click "Confirm" to save file.

File path of eeprom file, click "Confirm" to save file.


Then continue the last step to "start key writing"

Then continue the last step to "start key writing"

Start Key Writing
Note:
This function requires the device to connect to XP400 for performatin this function.

1. Please remove the RFA according to the Operation Guide, follow the guide to connect the chip correctly, and then read and save the EEPROM / DFLASH data.
2. Please save the stored data into the "Scan/UserData/JLRData" file in this device.

Start Key Writing

Select the Dflash and EEPROM file that you have saved, then choose a blank key position ID to make the dealer key.

Select the Dflash and EEPROM file

Click "
RFA_D-FLASH2020-04-27-151533.bin" file

Click "RFA_D-FLASH2020-04-27-151533.bin" file

"Are you sure to select RFA_D-FLASH2020-04-27-151533.bin file?"
Click "OK"

"Are you sure to select RFA_D-FLASH2020-04-27-151533.bin file?

" Click "OK"

Please select the EEPROM file.

Please select the EEPROM file.

Click "RFA_EEPROM2020-04-27-151623.bin" file


Click "RFA_EEPROM2020-04-27-151623.bin" file

Are you sure to select RFA_EEPROM2020-04-27-151623.bin file?
Click "OK"

Are you sure to select RFA_EEPROM2020-04-27-151623.bin file? Click 

"OK"

Select a key position that is blank
Click "Add Key" to Continue

Click "Add Key" to Continue

Please ensure that programmer is well connected and place the key to be added in the key sensing area of the programmer!

Please ensure that programmer is well connected and place the key to be 

added in the key sensing area of the programmer!

A dealer key is created successfully.

A dealer key is created successfully.

A new key ID has been created.

A new key ID has been created.

Do you want to exit the Start key writing function and save the new DFLASH and EEPROM dat file?
Click "Yes"

Do you want to exit the Start key writing function and save the new 

DFLASH and EEPROM dat file?

The data file is saved successfully.
Please use the Write into MCU function to write the newly create DFLASH and EEPROM data file into the RFA.
After the data writing is complete, install the smart box onto the vehicle, and verify if the newly added key can start the vehicle, and whether the remote controller is normal.
The name and directory of the newly created data file are as the following picutre:
Click "OK"

Click "OK"

Then go back to the menu Read / write chip Data to write the new created Dflash file and EEPROM file back to the MCU.



Click "Write MCU Data"




Click "D-FLASH"


Please select the DFLASH file



Write the new created Dflash file back to the MCU



Connecting to the programmer



Writing the chip, please wait...



Writing succeeded



Click "EEPROM"

Write the new created EEPROM file back to the MCU



Writing succeeded


Done